How to maintain CNC Router in winter
2.How to maintain CNC Router in winter
cnc router for stone with water cooling system, it in optimizing the stone cnc engraviong machine performance, at the same time itself also has limitations. Usually, a temperature suitable for engraving is between 0-45 degrees, when the temperature is below 0 degrees Celsius, the tap water used for cooling occurs frozen, will affect the use of the cnc machine. Moreover, stone cnc machine uses the relative humidity is between 30% -75%, too dry and too wet environment is not conducive to optimal play cnc machine control and power system. The winter dry environment is also not conducive to the normal use of the cnc machine.
So, in winter, you should pay attention to the warmth of the CNC Router engraving machine,timely removal of the remainder of the water in the aqueduct, avoid the next day freeze affect the water cycle; water pump should be promptly removed from multiply water tank or bucket, to avoid freezing in there. Secondly, we must pay attention to maintain the humidity within the plant, too dry, you can increase the number of times of mopping the floor, keep the plant the appropriate humidity. Suggest you do not put the machine on outdoor in winter, it is best to move the machine to the plant.
How to use CNC Router in different environment
3.how to use CNC Router in different environment
Stone cnc router / engraving machine to adapt to what the ambient temperature and humidity? Stone CNC Router / engraving machine, this big difference in the different environments and temperature. Stone engraving machine how to apply the changes in the environment, today there is the CNC Router Brand for you about the stone CNC Router / engraving machine how to apply the changes in the environment.
Required to do an environmental temperature should be in the range of 5-35degree. Special attention if below freezing environment.
After downtime required completely water shine; prevent circulating water freezes in the laser tube.
Current talent necessary to preheat for more than 5 minutes to boot. Rainy days and humid environment, the power required to preheat the hours are long, indeed Paishi caliber high pressure to prevent the breakdown of high voltage circuit.
Basic Operation Procedure Of Laser engraving machi
4.Basic Operation Procedure Of Laser engraving machine
Basic Operation Procedure Of Laser engraving machine
1) Start the water pump and air pump , let the water in laser tube circulate for 3 minutes.
2) Turn on the laser power ,and press “ray testing”button to see if there is ray.
3) Turn on the power of principal machine.
4) Turn on the power of blower fan
5) Operate the transmission file in the computer to start caving.
6) Start the controlling software; make sure that laser head can move left or right.
7) Put work pieces in position,and fix up the focal length(the length see Figure 3 ).
For cutting thick materisl,use focus lens of long focal length(2.5”=63.5mm).
For accurate engraving,use focus lens of short length(2”=50mm).
Turn off laser power,principal machine ,blower fan,water pump and air pump in turn.
Cautions and Maintenance of laser engraving machin
5.Cautions and Maintenance of laser engraving machine
Cautions and Maintenance of laser engraving machine
1.Please clean the machine after working every day .While cleaning , the crossbeam and Larry can be pushed gently and carefully in the condition that the power is turned off .Do not pull it strongly .
2.The minimum amount of cooling water should not be less then 30L . Make sure that the water can submerge the submersible pump .
3.If there is any question , please contact our custormer Service Department
4.Water tank , water pump and water inlet and out rubber tube should be cleaned once every four days.
5.Please clean the 1# and 2# reflecting lens on the machine carefully , otherwise , the ray path need readjustment !
6.If there is no special requirements, the ray intensity should be less then 80 percent, thus to avoid the tube aging quickly.
7.Water temperature should be examined at all times duing the working process . Once the water turns to warm , please change it righe away (the righe way of changing water is to get out of some hot water and fill
8. Please clean the working platform every time after working . Do not make dust flying in cold water ).
9.Please pay attention to the focal length before starting the machine every time . The accuracy of focal
10.Users should follow all the above-mentioned regulations carefully . Otherwise the manufacturer will not take responsibility for any troubles of the machine or physical in juries .
11.Lens should be cleaned once every day before starting the machine (Notice: It is not the time of being off duty).
12.The outer equipments (blower fan ,air pump ,etc .) should be cleaned once every two weeks .
length will greatly affect the carving effects .
13.Do not use circulating water of poor quality , because it may affect the laser power seriously and shorten the serice life of laser tube . The manufacturer is not responsible for repairing the laser tube damaged by the using of poor-qualified water .It is suggested to use purified water or distilled water .
14. Guide rails should be cleaned and lubricated once exery two weeks .